List of drill and tap sizes

Below is a comprehensive drill and tap size chart for all drills and taps: Inch, imperial, and metric, up to 36.5 millimetres (1.44 in) in diameter.

Schematic of a machine tap

In manufactured parts, holes with female screw threads are often needed; they accept male screws to facilitate the building and fastening of a finished assembly. One of the most common ways to produce such threaded holes is to drill a hole of appropriate size with a drill bit and then tap it with a tap. Each standard size of female screw thread has one or several corresponding drill bit sizes that are within the range of appropriate size—slightly larger than the minor diameter of the mating male thread, but smaller than its pitch and major diameters. Such an appropriately sized drill is called a tap drill for that size of thread, because it is a correct drill to be followed by the tap. Many thread sizes have several possible tap drills, because they yield threads of varying thread depth between 50% and 100%. Usually thread depths of 60% to 75% are desired.

People frequently use a chart such as this to determine the proper tap drill for a certain thread size or the proper tap for an existing hole.

Rules of thumb

Regarding the proportion of tap drill to thread major diameter, for standard V threads (ISO V thread and UTS V thread), there are several rules of thumb with strong predictive power:

• A good tap drill is 85% (± 2 pp) of major diameter for coarse threads, and 90% (± 2 pp) of major diameter for fine threads. ^[1]
• For metric V threads, the concept of major minus pitch (i.e., the major or widest diameter of the intended screw in millimeters minus the pitch of the threads of that screw in millimeters per thread) yields a good tap drill diameter.
  The major minus pitch technique also works for inch-based threads, but you must first calculate the pitch by converting the fraction of threads-per-inch (TPI) into a decimal. For example, a screw with a pitch of 1/20 in (20 threads per inch) has a pitch of 0.050 in and a 1⁄13 in pitch (13 threads per inch) has a pitch of 0.077 in. Your result will only land near a tap drill size (not directly on one).
• For both of these rules of thumb (85%/90% and major minus pitch), the tap drill size yielded is not necessarily the only possible one, but it is a good one for general use.
• The 85% and 90% rules works best in the range of 1⁄4–1 in (6.4–25.4 mm), the sizes most important on many shop floors. Some sizes outside that range have different ratios.

Below, these guidelines are explored with examples.

Examples

• • Example (inch, coarse): For size 7⁄16 (this is the diameter of the intended screw in fraction form)-14 (this is the number of threads per inch; 14 is considered coarse), 0.437 in × 0.85 = 0.371 in. Therefore, a size 7⁄16 screw (7⁄16 ≈ 0.437) with 14 threads per inch (coarse) needs a tap drill with a diameter of about 0.371 inches.
    • The drill sizes that are near this are letter U (0.368 in; 84.2%), 9.5 mm (0.374 in; 85.6%), and 3⁄8 in (0.375 in; 85.8%); any of these will work well.
  • Example (inch, fine): For 7⁄16-20 (same diameter as the previous example, but this time with 20 threads per inch, which is considered fine), 0.437 in × 0.90 = 0.393 in (i.e., if the threads are to be fine, then a slightly larger diameter drill bit should be used before tapping the hole for the screw).
    • The drill sizes that are near this are 25⁄64 (0.391 in; 89.4%), 10 mm (0.393 in; 90%), and letter X (0.397 in; 90.8%); any of these will work well.
  • Example (metric, coarse): For M7.0×1.0 (an intended screw with a diameter of 7.0 mm and a pitch of 1 mm between each thread, which is considered coarse), 7.0 mm × 0.85 = 5.95 mm.
    • The drill sizes that are near this are 15⁄64 in (85%), 6.0 mm (85.7%), and 6.1 mm (87.1%); any of these will work well.
  • Example (metric, fine): For M7.0×0.5, 7.0 mm × 0.90 = 6.30.
    • The drill sizes that are near this are 6.3 mm (90%), 1⁄4 in (90.7%), 6.4 mm (91.4%), and 6.5 mm (92.9%); any of these will work well.
• For metric V threads, major minus pitch yields a good tap drill diameter.
  • Example (metric, coarse): For M7.0 × 1.0, 7.0 − 1.0 = 6.0
  • Example (metric, fine): For M7.0 × 0.5, 7.0 − 0.5 = 6.5
    • (The 85% coarse, 90% fine guideline, within its effective range, matches this in net effect)
  • The major minus pitch also works for inch-based threads, but you must first determine the pitch by looking at the number of treads per inch (TPI; for example, 1⁄20 = 0.050 and 1⁄13 ≈ 0.077), and your result will only land near a tap drill size (not directly on one).
  • Example (inch coarse): For 7⁄16-14, 1 in ÷ 14 = 0.071 in; 0.437 in − 0.071 in = 0.366 in;
    • The drill sizes that are near this are 9.3 mm (0.366 in) and letter U (0.368 in). In addition, 9.5 mm (0.374 in), and 3⁄8 in (0.375 in) will work well, although major minus pitch by itself does not tell you this; but the 85% ± 2 pp guideline supports it.
  • Example (inch fine): For 7⁄16-20, 1 in ÷ 20 = 0.050 in; 0.437 in − 0.050 in = 0.387 in;
    • The drill sizes that are near this are letter W (0.386 in) and 25⁄64 in (0.391 in). In addition, 10 mm (0.393 in), and letter X (0.397 in) will work well, although major minus pitch by itself does not tell you this; but the 90% ± 2 pp guideline supports it.
• For both of these rules of thumb (85%/90% and major minus pitch), the tap drill size yielded is not necessarily the only possible one, but it is a good one for general use.
  • Example (metric coarse): For M7.0×1.0, major minus pitch yields 6.0, but 6.1 also works well.
  • Example (metric fine): For M7.0×0.5, major minus pitch yields 6.5, which at 92.9% happens to be an example that pushes over the outer bound of the 90% ± 2 pp, but major minus pitch is still valid, although smaller drills (6.3 mm, 1⁄4, 6.4 mm) will work well.

Chart

  Inch-sized drills, increments of 1⁄64 in.

  Drills in the number (1–80) and letter (A–Z) series which are specified in decimal inches.

  Standard metric drill sizes.

  Standard metric drill sizes used for metric taps of the size indicated in the tap size column.

Drill bit diameter		Fractional size	Drill wire  gauge[2][3]	Tap size[4][5][6]	Clearance		Thread depth†[7][8] (%)	Outer diameter
(mm, 4 d.p.)	(in, 5 d.p.)	(in)			Close fit[9]	Free fit[10]
0.0483	0.00190		107
0.0500	0.00197
0.0584	0.00230		106
0.0686	0.00270		105
0.0787	0.00310		104
0.0889	0.00350		103
0.0991	0.00390		102
0.1000	0.00394
0.1092	0.00430		101
0.1194	0.00470		100
0.1295	0.00510		99
0.1397	0.00550		98
0.1499	0.00590		97
0.1600	0.00630		96
0.1702	0.00670		95
0.1803	0.00710		94
0.1905	0.00750		93
0.2007	0.00790		92
0.2000	0.00787
0.2108	0.00830		91
0.2210	0.00870		90
0.2311	0.00910		89
0.2413	0.00950		88
0.2500	0.00984
Drill bit diameter		Fractional size	Drill wire  gauge[2][3]	Tap size[4][5][6]	Clearance		Thread depth†[11][8] (%)	Outer diameter
(mm, 4 d.p.)	(in, 5 d.p.)	(in)			Close fit[9]	Free fit[10]
0.2540	0.01000		87
0.2667	0.01050		86
0.2794	0.01100		85
0.2921	0.01150		84
0.3000	0.01181
0.3048	0.01200		83
0.3175	0.01250		82
0.3302	0.01300		81
0.3429	0.01350		80
0.3500	0.01378
0.3680	0.01449		79
0.3969	0.01563	1⁄64		#0000-160‡	0.02400 in			0.021 in
0.4000	0.01575
0.4064	0.01600		78
0.4200	0.01654
0.4400	0.01732
0.4500	0.01772
0.4572	0.01800		77
0.4600	0.01811
0.4800	0.01890
0.5000	0.01969
0.5080	0.02000		76
0.5334	0.02100		75
0.5500	0.02165
Drill bit diameter		Fractional size	Drill wire  gauge[2][3]	Tap size[4][5][6]	Clearance		Thread depth†[12][8] (%)	Outer diameter
(mm, 4 d.p.)	(in, 5 d.p.)	(in)			Close fit[9]	Free fit[10]
0.5715	0.02250		74
0.6000	0.02362
0.6096	0.02400		73
0.6350	0.02500		72
0.6500	0.02559
0.6604	0.02600		71	#000-120‡	0.03700 in
0.7000	0.02756
0.7112	0.02800		70
0.7417	0.02920		69
0.7500	0.02953
0.7874	0.03100		68
0.7938	0.03125	1⁄32
0.8000	0.03150
0.8128	0.03200		67
0.8382	0.03300		66
0.8500	0.03346
0.8890	0.03500		65	#00-90‡	0.05200 in
0.9000	0.03543
0.9144	0.03600		64
0.9398	0.03700		63
0.9500	0.03740
0.9652	0.03800		62
0.9906	0.03900		61
1.0000	0.03937
1.0160	0.04000		60
Drill bit diameter		Fractional size	Drill wire  gauge[2][3]	Tap size[4][5][6]	Clearance		Thread depth†[13][8] (%)	Outer diameter
(mm, 4 d.p.)	(in, 5 d.p.)	(in)			Close fit[9]	Free fit[10]
1.0414	0.04100		59
1.0500	0.04134
1.0668	0.04200		58
1.0922	0.04300		57
1.1000	0.04331
1.1500	0.04528
1.1811	0.04650		56
1.1906	0.04688	3⁄64		#0–80	0.06350 in	0.07000 in
1.2000	0.04724
1.2500	0.04921
1.3000	0.05118
1.3208	0.05200		55
1.3500	0.05315
1.3970	0.05500		54
1.4000	0.05512
1.4500	0.05709
1.5000	0.05906
1.5113	0.05950		53	#1–64, #1–72	0.07600 in	0.08100 in
1.5500	0.06102
1.5875	0.06250	1⁄16
1.6000	0.06299			M2×0.4	2.2 mm
1.6129	0.06350		52
1.6500	0.06496
1.7000	0.06693
1.7018	0.06700		51	#2–56	0.08900 in	0.09600 in
1.7500	0.06890			M2.2×0.45	2.25 mm
Drill bit diameter		Fractional size	Drill wire  gauge[2][3]	Tap size[4][5][6]	Clearance		Thread depth†[14][8] (%)	Outer diameter
(mm, 4 d.p.)	(in, 5 d.p.)	(in)			Close fit[9]	Free fit[10]
1.7780	0.07000		50	#2–56, #2–64	0.08900 in	0.09600 in
1.8000	0.07087
1.8500	0.07283
1.8542	0.07300		49
1.9000	0.07480
1.9304	0.07600		48
1.9500	0.07677
1.9600	0.07717			#3–48	0.10400 in	0.11000 in	81
1.9700	0.07756			#3–48	0.10400 in	0.11000 in	79
1.9844	0.07813	5⁄64		#3–48	0.10400 in	0.11000 in	78
1.9939	0.07850		47	#3–48	0.10400 in	0.11000 in	76
2.0000	0.07874			#3–48	0.10400 in	0.11000 in	75
2.0100	0.07913			#3–48	0.10400 in	0.11000 in	74
2.0200	0.07953			#3–48	0.10400 in	0.11000 in	72
2.0300	0.07992			#3–48	0.10400 in	0.11000 in	71
2.0400	0.08031			#3–48 #3–56	0.10400 in	0.11000 in	69 81
2.0500	0.08071			#3–48 #3–56 M2.5×0.45	0.10400 in	0.11000 in	68 79
2.0574	0.08100		46	#3–48 #3–56	0.10400 in	0.11000 in	66 77
2.0700	0.08150			#3–48 #3–56	0.10400 in	0.11000 in	65 75
2.0828	0.08200		45	#3–48 #3–56	0.10400 in	0.11000 in	66 74
2.0900	0.08228			#3–48 #3–56	0.10400 in	0.11000 in	62 72
2.1000	0.08268			#3–48 #3–56	0.10400 in	0.11000 in	60 70
2.1100	0.08307			#3–48 #3–56	0.10400 in	0.11000 in	59 69
2.1200	0.08346			#3–56	0.10400 in	0.11000 in	67
2.1300	0.08386			#3–56	0.10400 in	0.11000 in	65
2.1400	0.08425			#3–56	0.10400 in	0.11000 in	63
2.1500	0.08465			#3–56 M2.5×0.35	0.10400 in	0.11000 in	62
2.1600	0.08504			#3–56	0.10400 in	0.11000 in	60
2.1700	0.08543			#3–56	0.10400 in	0.11000 in	59
2.1844	0.08600		44	#4–36	0.11600 in	0.12850 in	81
2.1900	0.08622			#4–40	0.11600 in	0.12850 in	81
2.2000	0.08661			#4–40	0.11600 in	0.12850 in	78
2.2100	0.08701			#4–40	0.11600 in	0.12850 in	77
2.2200	0.08740			#4–40	0.11600 in	0.12850 in	76
2.2300	0.08780			#4–40	0.11600 in	0.12850 in	75
2.2400	0.08819			#4–40	0.11600 in	0.12850 in	73
2.2500	0.08858			#4–40	0.11600 in	0.12850 in	72
2.2600	0.08898			#4–40	0.11600 in	0.12850 in	71
2.2606	0.08900		43	#4–40	0.11600 in	0.12850 in	71
2.2700	0.08937			#4–40	0.11600 in	0.12850 in	70
2.2800	0.08976			#4–40	0.11600 in	0.12850 in	68
2.2900	0.09016			#4–40 #4–48	0.11600 in	0.12850 in	67 81
2.3000	0.09055			#4–40 #4–48	0.11600 in	0.12850 in	66 79
2.3100	0.09094			#4–40 #4–48	0.11600 in	0.12850 in	65 78
2.3200	0.09134			#4–40 #4–48	0.11600 in	0.12850 in	64 76
2.3300	0.09173			#4–40 #4–48	0.11600 in	0.12850 in	63 75
2.3400	0.09213			#4–40 #4–48	0.11600 in	0.12850 in	61 74
2.3500	0.09252			#4–40 #4–48	0.11600 in	0.12850 in	60 72
2.3749	0.09350		42	#4–48	0.11600 in	0.12850 in	69
2.3813	0.09375	3⁄32
2.4000	0.09449
2.4384	0.09600		41
2.4500	0.09646
2.4892	0.09800		40
2.5000	0.09843			M3×0.5	3.2 mm		75
2.5273	0.09950		39	#5–40	0.12850 in	0.13600 in	78
2.5781	0.10150		38	#5–40	0.12850 in	0.13600 in	72
2.6000	0.10236
2.6416	0.10400		37	#5–44	0.12850 in	0.13600 in	71
2.7000	0.10630
2.7051	0.10650		36	#6–32	0.14400 in	0.14950 in	77	0.14 in
2.7500	0.10827
2.7781	0.10938	7⁄64
2.7940	0.11000		35
2.8000	0.11024
2.8194	0.11100		34
2.8702	0.11300		33	#6–40		0.1563 in		0.14 in
2.9000	0.11417			M3.5×0.6
2.9464	0.11600		32
3.0000	0.11811
3.0480	0.12000		31	#6–48
3.1000	0.12205
3.1750	0.12500	1⁄8
3.2000	0.12598
3.2500	0.12795
3.2639	0.12850		30
3.3000	0.12992			M4×0.7	4.10 mm		75
3.4000	0.13386
3.4544	0.13600		29	#8–32, #8–36	0.16950 in	0.17700 in	69
3.5000	0.13780			M4×0.5	4.10 mm		60
3.5687	0.14050		28	#8–40
3.5719	0.14063	9⁄64
3.6000	0.14173
3.6576	0.14400		27
3.7000	0.14567
3.7338	0.14700		26
3.7500	0.14764
3.7973	0.14950		25	#10–24	0.19600 in	0.20100 in	75
3.8000	0.14961
3.8608	0.15200		24
3.9000	0.15354
3.9116	0.15400		23
3.9688	0.15625	5⁄32
3.9878	0.15700		22
4.0000	0.15748
4.0386	0.15900		21	#10–32	0.1960 in	0.2010 in
4.0894	0.16100		20
4.1000	0.16142
4.2000	0.16535			M5×0.8	5.10 mm		75
4.2164	0.16600		19
4.2500	0.16732
4.3053	0.16950		18
4.3656	0.17188	11⁄64
4.3942	0.17300		17
4.4000	0.17323
4.4958	0.17700		16	#12–24	0.22100 in	0.22800 in	72
4.5000	0.17717
4.5720	0.18000		15
4.6000	0.18110
4.6228	0.18200		14
4.6990	0.18500		13
4.7000	0.18504
4.7500	0.18701
4.7625	0.18750	3⁄16
4.8000	0.18898
4.8006	0.18900		12
4.8514	0.19100		11
4.9000	0.19291
4.9149	0.19350		10
4.9784	0.19600		9
5.0000	0.19685			M6×1.0	6.10 mm		75
5.0546	0.19900		8
5.1000	0.20079
5.1054	0.20100		7	1⁄4-20	0.25700 in	0.26600 in	72
5.1594	0.20313	13⁄64
5.1816	0.20400		6
5.2000	0.20472			M6×0.75 [15]	6.10 mm		60
5.2197	0.20550		5
5.2500	0.20669
5.3000	0.20866
5.3086	0.20900		4
5.4000	0.21260
5.4102	0.21300		3	1⁄4-28	0.25700 in	0.26600 in	80
5.5000	0.21654			1⁄4-28	0.25700 in	0.26600 in	70
5.5563	0.21875	7⁄32		1⁄4-28 1⁄4-32 (1⁄4-32 UNEF for glow plugs)	0.25700 in	0.26600 in	68
5.6000	0.22047			1⁄4-28	0.25700 in	0.26600 in	63
5.6134	0.22100		2	1⁄4-28	0.25700 in	0.26600 in	60
5.7000	0.22441
5.7500	0.22638
5.7912	0.22800		1
5.8000	0.22835
5.9000	0.23228
5.9436	0.23400		A
5.9531	0.23438	15⁄64
6.0000	0.23622
6.0452	0.23800		B
6.1000	0.24016			M7×1.0			75
6.1468	0.24200		C	1⁄16-27 NPT
6.2000	0.24409
6.2484	0.24600		D
6.2500	0.24606
6.3000	0.24803
6.3500	0.25000	1⁄4
			E
6.4000	0.25197
6.5000	0.25591			M7×0.5
6.5278	0.25700		F	5⁄16-18	0.32300 in	0.33200 in	77
6.6000	0.25984
6.6294	0.26100		G
6.7000	0.26378
6.7469	0.26563	17⁄64		5⁄16-18			74
6.7500	0.26575
6.7564	0.26600		H
6.8000	0.26772
6.9000	0.27165			M8×1.25			75
6.9088	0.27200		I	5⁄16-24	0.32300 in	0.33200 in	75
7.0000	0.27559
7.0358	0.27700		J	5⁄16-18			50
7.1000	0.27953			M8×1.0			75
7.1374	0.28100		K
7.1438	0.28125	9⁄32		5⁄16-32
7.2000	0.28346
7.2500	0.28543
7.3000	0.28740
7.3660	0.29000		L
7.4000	0.29134
7.4930	0.29500		M
7.5000	0.29528
7.5406	0.29688	19⁄64
7.6000	0.29921
7.6708	0.30200		N
7.7000	0.30315
7.7500	0.30512
7.8000	0.30709
7.9000	0.31102
7.9375	0.31250	5⁄16		3⁄8-16	0.38600 in	0.39700 in	77
8.0000	0.31496
8.0264	0.31600		O
8.1000	0.31890
8.2000	0.32283
8.2042	0.32300		P
8.2500	0.32480
8.3000	0.32677
8.3344	0.32813	21⁄64
8.4000	0.33071
8.4328	0.33200		Q	3⁄8-24	0.38600 in	0.39700 in	79
8.5000	0.33465			M10×1.5
8.6000	0.33858
8.6106	0.33900		R	1⁄8-27 NPT
8.7000	0.34252
8.7313	0.34375	11⁄32
8.7500	0.34449			M10×1.25
8.8000	0.34646
8.8392	0.34800		S
8.9000	0.35039
9.0000	0.35433			M10×1.0 (spark plug)
9.0932	0.35800		T
9.1000	0.35827
9.1281	0.35938	23⁄64
9.2000	0.36220
9.2500	0.36417
9.3000	0.36614
9.3472	0.36800		U	7⁄16-14	0.45310 in	0.46870 in	75
9.4000	0.37008
9.5000	0.37402
9.5250	0.37500	3⁄8
9.5758	0.37700		V
9.6000	0.37795
9.7000	0.38189
9.7500	0.38386
9.8000	0.38583
9.8044	0.38600		W
9.9000	0.38976
9.9219	0.39063	25⁄64		7⁄16-20	0.45313 in	0.46785 in	72
10.0000	0.39370
10.0838	0.39700		X
10.2616	0.40400		Y
10.3188	0.40625	13⁄32		7⁄16-40
10.4902	0.41300		Z
10.5000	0.41339			M12×1.75			75
10.7000	0.42126			M12×1.5			75
10.7156	0.42188	27⁄64		1⁄2-13	0.51563 in	0.53125 in	78
10.900	0.42913			M12×1.25 (spark plug)
11.0000	0.43307
11.1125	0.43750	7⁄16		1⁄4-18 NPT
11.5000	0.45276
11.5094	0.45313	29⁄64		1⁄2-20	0.51563 in	0.53125 in	72
11.9063	0.46875	15⁄32		9⁄16-12	0.56250 in		87
12.0000	0.47244
12.2000	0.48031			M14×2			75
12.3031	0.48438	31⁄64		9⁄16-12	0.56250 in		68
12.5000	0.49213
12.7000	0.50000	1⁄2		9⁄16-18	0.56250 in		87
				M14×1.5			75
12.8000	0.50393			M14×1.25 (spark plug)
13.0000	0.51181
13.0969	0.51563	33⁄64		9⁄16-18	0.56250 in		65
13.4938	0.53125	17⁄32		5⁄8-11	0.62500 in		79
13.5000	0.53150
13.8906	0.54688	35⁄64		5⁄8-11	0.62500 in		66
14.0000	0.55118
14.2000	0.55906			M16×2			75
14.2875	0.56250	9⁄16		5⁄8-18	0.62500 in		87
14.5000	0.57087
14.6844	0.57813	37⁄64		5⁄8-18 3⁄8-18 NPT	0.62500 in		65
14.7000	0.57874			M16×1.5			75
15.0000	0.59055
15.0813	0.59375	19⁄32
15.4781	0.60938	39⁄64
15.5000	0.61024
15.8750	0.62500	5⁄8
16.0000	0.62992
16.2719	0.64063	41⁄64		3⁄4-10			84
16.5000	0.64961
16.6688	0.65625	21⁄32		3⁄4-10			72
16.8000	0.66141			M18×1.5 (spark plug)
17.0000	0.66929
17.0656	0.67188	43⁄64
17.4625	0.68750	11⁄16		3⁄4-16			77
17.5000	0.68898
17.8594	0.70313	45⁄64
18.0000	0.70866
18.2563	0.71875	23⁄32		1⁄2-14 NPT
18.5000	0.72835
18.6531	0.73438	47⁄64
19.0000	0.74803
19.0500	0.75000	3⁄4
19.4469	0.76563	49⁄64		7⁄8-9			76
19.5000	0.76772
19.8438	0.78125	25⁄32		7⁄8-9			65
20.0000	0.78740
20.2406	0.79688	51⁄64		7⁄8-14			84
20.5000	0.80709
20.6375	0.81250	13⁄16		7⁄8-14			67
21.0000	0.82677
21.0344	0.82813	53⁄64		7⁄8-18 NS (spark plug)
21.4313	0.84375	27⁄32
21.5000	0.84646
21.8281	0.85938	55⁄64		1–8			87
22.0000	0.86614
22.2250	0.87500	7⁄8		1–8			77
22.5000	0.88583
22.6219	0.89063	57⁄64		1–8			67
23.0000	0.90551
23.0188	0.90625	29⁄32		1–12			87
23.4156	0.92188	59⁄64		1–12 1–14 3⁄4-14 NPT			72 84
23.5000	0.92520
23.8125	0.93750	15⁄16		1–14			67
24.0000	0.94488
24.2094	0.95313	61⁄64
24.5000	0.96457
24.6063	0.96875	31⁄32		1+1⁄8-7			84
25.0000	0.98425
25.0031	0.98438	63⁄64		1+1⁄8-7			76
25.4000	1.00000	1		1+1⁄8-7			67
25.5000	1.00394
25.7969	1.01563	1+1⁄64
26.0000	1.02362
26.1938	1.03125	1+1⁄32		1+1⁄8-12			87
26.5000	1.04331
26.5906	1.04688	1+3⁄64		1+1⁄8-12			72
26.9875	1.06250	1+1⁄16
27.0000	1.06299
27.5000	1.08268
28.0000	1.10236
28.1781	1.10938	1+7⁄64		1+1⁄4-7			76
28.5000	1.12205
28.5750	1.12500	1+1⁄8		1+1⁄4-7			67
29.0000	1.14173
29.3688	1.15625	1+5⁄32		1+1⁄4-12 1-11+1⁄2 NPT			87
29.5000	1.16142
29.7656	1.17188	1+11⁄64		1+1⁄4-12			72
30.0000	1.18110
30.1625	1.18750	1+3⁄16		1+3⁄8-6			87
30.5000	1.20079
30.5594	1.20313	1+13⁄64		1+3⁄8-6			79
30.9563	1.21875	1+7⁄32		1+3⁄8-6			72
31.0000	1.22047
31.3531	1.23438	1+15⁄64		1+3⁄8-6			65
31.5000	1.24016
32.0000	1.25984
32.5000	1.27953
32.5438	1.28125	1+9⁄32		1+3⁄8-12			87
32.9406	1.29688	1+19⁄64		1+3⁄8-12			72
33.0000	1.29921
33.3375	1.31250	1+5⁄16		1+1⁄2-6			87
33.5000	1.31890
33.7344	1.32813	1+21⁄64		1+1⁄2-6			79
34.0000	1.33858
34.1313	1.34375	1+11⁄32		1+1⁄2-6			72
34.5000	1.35827
34.5281	1.35938	1+23⁄64		1+1⁄2-6			65
35.0000	1.37795
35.5000	1.39764
35.7188	1.40625	1+13⁄32		1+1⁄2-12			87
36.0000	1.41732
36.1156	1.42188	1+27⁄64		1+1⁄2-12			72
36.5000	1.43701

^†If theoretical thread percentage not given, assume 75% ± 10%
  Theoretical percentage of thread should not be relied upon for threads of included angles other than 60 degrees.
^‡See http://www.newmantools.com/taps/micro.htm for more information.

See also

• AN thread
• British standard pipe thread
• British Association screw threads
• British Standard Whitworth
• Drill bit sizes, a similar page including center drill sizes
• ISO metric screw thread
• National pipe thread
• Taps and dies
• United States Standard thread
• Unified Thread Standard