Mercedes-Benz first series automatic transmission

The Mercedes-Benz first series of automatic transmission was produced from 1961 to 1983 in 4- and 3-speed variants for Mercedes-Benz passenger cars. In addition, variants for commercial vehicles were offered.

Mercedes-Benz K4A 025 K4B 050 · K4C 025 · K4A 040 W3A 040 · W3B 050 · W4B 025 W4A 018 · W4B 035
K4A 025
Overview
Manufacturer	Daimler AG
Production	1961–1983
Body and chassis
Class	3 and 4-speed longitudinal automatic transmission
Chronology
Successor	4G-Tronic

This transmission was the first Mercedes-Benz automatic transmission in-house developing.^[1] Before this, the company used semi-automatic systems like a vacuum-powered shifting for overdrive or the "Hydrak" hydraulic automatic clutch system. Alternatively, they bought automatic transmissions of other vendors, such as the Detroit gear 3-speed automatic transmission from BorgWarner for the 300 c and 300 d (not to be confused with the later 300 D and its successors).

The automatic transmissions are for engines with longitudinal layout for rear-wheel-drive layout passenger cars. The control of the fully automatic system is fully hydraulic and it uses electrical wire only for the kickdown solenoid valve and the neutral safety switch.

Physically, it can be recognized for its pan which uses 16 bolts.

Gear Ratios^[a]

Gear Model	R	1	2	3	4	Total Span	Span Center	Avg. Step	Compo- nents
K4A 025 · 1961	−4.145	3.979	2.520	1.579	1.000	3.979	1.995	1.585	2 Gearsets 3 Brakes 3 Clutches
K4B 050 · 1964	−4.145	3.979	2.459	1.579	1.000	3.979	1.995	1.585	3 Gearsets 3 Brakes 2 Clutches
K4C 025 · 1967 K4A 040 · 1969 W4B 025 · 1972	−5.478	3.983	2.386	1.461	1.000	3.983	1.996	1.585
W4A 018 · 1975	−5.499	4.006	2.391	1.463	1.000	4.006	2.001	1.588
W4B 035 · 1975	−5.881	4.176	2.412	1.462	1.000	4.176	2.043	1.610
W3A 040 · 1971 W3A 050 · 1973 W3A 050 reinf. · 1975	−1.836	2.306	1.461	1.000		2.306	1.519	1.519	2 Gearsets 3 Brakes 2 Clutches
Differences in gear ratios have a measurable, direct impact on vehicle dynamics, performance, waste emissions as well as fuel mileage

1961: K4A 025 — 4-Speed Transmission With 2 Planetary Gearsets —

K4A 025 transmission left hand side view

K4A 025 transmission right hand side view

Layout

The K4A 025^[a] (without type designation) is the first of the series, launched in April 1961 for the W 111 220 SEb, later replaced with the more reliable K4C 025 (type 722.2). It is a 4-speed unit and uses fluid coupling (also referred in some manuals as hydraulic/automatic clutch).

The design of the transmission results in poor shifting comfort, which does not meet Mercedes-Benz standards. This applies in particular to the change from 2nd to 3rd gear (and vice versa), which requires a group change, i.e. affects all shift elements.

Specifications

For this first 4-speed model^[b] 8 main components^[c] are used. It is the only exemption which uses only 2 planetary gearsets for 4 speeds.

1. Kupplungs-4-Gang-Automatik bis 25 kpm Eingangsdrehmoment
   (clutch-4-gear-automatic with 25 kp⋅m (181 lb⋅ft) maximum input torque
2. plus 1 reverse gear
3. 2 simple planetary gearsets, 3 brakes, 3 clutches

Gear Ratios

With Assessment		Planetary Gearset: Teeth Simple[a]		Count	Total[b] Center[c]	Avg.[d]
Model Type	Version First Delivery	S1[e] R1[f]	S2[g] R2[h]	Brakes Clutches	Ratio Span	Gear Step[i]
Gear Ratio		R ${\displaystyle {i_{R}}}$	1 ${\displaystyle {i_{1}}}$	2 ${\displaystyle {i_{2}}}$	3 ${\displaystyle {i_{3}}}$	4 ${\displaystyle {i_{4}}}$
Step[i]		${\displaystyle -{\tfrac {i_{R}}{i_{1}}}}$[j]	${\displaystyle {\tfrac {i_{1}}{i_{1}}}}$	${\displaystyle {\tfrac {i_{1}}{i_{2}}}}$[k]	${\displaystyle {\tfrac {i_{2}}{i_{3}}}}$	${\displaystyle {\tfrac {i_{3}}{i_{4}}}}$
Δ Step[l][m]				${\displaystyle {\tfrac {i_{1}}{i_{2}}}:{\tfrac {i_{2}}{i_{3}}}}$	${\displaystyle {\tfrac {i_{2}}{i_{3}}}:{\tfrac {i_{3}}{i_{4}}}}$
Shaft Speed		${\displaystyle {\tfrac {i_{1}}{i_{R}}}}$	${\displaystyle {\tfrac {i_{1}}{i_{1}}}}$	${\displaystyle {\tfrac {i_{1}}{i_{2}}}}$	${\displaystyle {\tfrac {i_{1}}{i_{3}}}}$	${\displaystyle {\tfrac {i_{1}}{i_{4}}}}$
Δ Shaft Speed[n]		${\displaystyle 0-{\tfrac {i_{1}}{i_{R}}}}$	${\displaystyle {\tfrac {i_{1}}{i_{1}}}-0}$	${\displaystyle {\tfrac {i_{1}}{i_{2}}}-{\tfrac {i_{1}}{i_{1}}}}$	${\displaystyle {\tfrac {i_{1}}{i_{3}}}-{\tfrac {i_{1}}{i_{2}}}}$	${\displaystyle {\tfrac {i_{1}}{i_{4}}}-{\tfrac {i_{1}}{i_{3}}}}$
K4A 025 N/A	25 kp⋅m (181 lb⋅ft) 1961[2][3]	50 76	44 76	3 3	3.9789 1.9947	1.5846[i]
Gear Ratio		−4.1455 ${\displaystyle -{\tfrac {228}{55}}}$	3.9789 ${\displaystyle {\tfrac {378}{95}}}$	2.5200[i][m] ${\displaystyle {\tfrac {63}{25}}}$	1.5789[i] ${\displaystyle {\tfrac {30}{19}}}$	1.0000 ${\displaystyle {\tfrac {1}{1}}}$
Step		1.0418	1.0000	1.5789[i]	1.5960[i]	1.5789
Δ Step[l]				0.9893[m]	1.0108
Speed		-0.9598	1.0000	1.5789	2.5200	3.9789
Δ Speed		0.9598	1.0000	0.5789	0.9411	1.4589
Ratio R & Even		${\displaystyle -{\tfrac {R_{1}(S_{2}+R_{2})}{S_{1}S_{2}}}}$	${\displaystyle {\tfrac {S_{1}+R_{1}}{S_{1}}}}$		${\displaystyle {\tfrac {1}{1}}}$
Ratio Odd			${\displaystyle {\tfrac {(S_{1}+R_{1})(S_{2}+R_{2})}{S_{1}R_{2}}}}$		${\displaystyle {\tfrac {S_{2}+R_{2}}{R_{2}}}}$
Algebra And Actuated Shift Elements
Brake A[o]			❶	❶
Brake B[p]			❶		❶
Brake R[q]		❶
Clutch D[r]					❶	❶
Clutch E[s]		❶
Clutch F[t]				❶		❶
Layout Input and output are on opposite sides Planetary gearset 1 is on the input (turbine) side Input shafts is S1 and, if actuated, C1 (the carrier of gearset 1) Output shaft is C2 (the carrier of gearset 2) Total Ratio Span (Total Ratio Spread · Total Gear Ratio) ${\displaystyle {\tfrac {i_{1}}{i_{n}}}}$ A wider span enables the downspeeding when driving outside the city limits increase the climbing ability when driving over mountain passes or off-road or when towing a trailer Ratio Span's Center ${\displaystyle (i_{1}i_{n})^{\tfrac {1}{2}}}$ The center indicates the speed level of the transmission Together with the final drive ratio it gives the shaft speed level of the vehicle Average Gear Step ${\displaystyle ({\tfrac {i_{1}}{i_{n}}})^{\tfrac {1}{n-1}}}$ With decreasing step width the gears connect better to each other shifting comfort increases Sun 1: sun gear of gearset 1 Ring 1: ring gear of gearset 1 Sun 2: sun gear of gearset 2 Ring 2: ring gear of gearset 2 Standard 50:50 — 50 % Is Above And 50 % Is Below The Average Gear Step — With steadily decreasing gear steps (yellow highlighted line Step) and a particularly large step from 1st to 2nd gear the lower half of the gear steps (between the small gears; rounded down, here the first 1) is always larger and the upper half of the gear steps (between the large gears; rounded up, here the last 2) is always smaller than the average gear step (cell highlighted yellow two rows above on the far right) lower half: smaller gear steps are a waste of possible ratios (red bold) upper half: larger gear steps are unsatisfactory (red bold) Standard R:1 — Reverse And 1st Gear Have The Same Ratio — The ideal reverse gear has the same transmission ratio as 1st gear no impairment when maneuvering especially when towing a trailer a torque converter can only partially compensate for this deficiency Plus 11.11 % minus 10 % compared to 1st gear is good Plus 25 % minus 20 % is acceptable (red) Above this is unsatisfactory (bold) Standard 1:2 — Gear Step 1st To 2nd Gear As Small As Possible — With continuously decreasing gear steps (yellow marked line Step) the largest gear step is the one from 1st to 2nd gear, which for a good speed connection and a smooth gear shift must be as small as possible A gear ratio of up to 1.6667:1 (5:3) is good Up to 1.7500:1 (7:4) is acceptable (red) Above is unsatisfactory (bold) From large to small gears (from right to left) Standard STEP — From Large To Small Gears: Steady And Progressive Increase In Gear Steps — Gear steps should increase: Δ Step (first green highlighted line Δ Step) is always greater than 1 As progressive as possible: Δ Step is always greater than the previous step Not progressively increasing is acceptable (red) Not increasing is unsatisfactory (bold) Standard SPEED — From Small To Large Gears: Steady Increase In Shaft Speed Difference — Shaft speed differences should increase: Δ Shaft Speed (second line marked in green Δ (Shaft) Speed) is always greater than the previous one 1 difference smaller than the previous one is acceptable (red) 2 consecutive ones are a waste of possible ratios (bold) Blocks R1 Blocks S2 Blocks C1(the carrier of gearset 1) Couples C1 (the carrier of gearset 2) with the turbine Couples R1 with S2 Couples S2 with R2

1964: K4B 050 And Follow-Up Products — 4-Speed Transmissions With 3 Planetary Gearsets —

Layout

The Mercedes-Benz 600 from April 1964, the first post-war "Grand Mercedes", is powered by the Mercedes-Benz M100 engine.This made a gearbox for the highest demands of luxury vehicles necessary. The design of the gearbox in the range was out of the question from the outset. The introduction of the 600 was therefore taken as an opportunity to develop a completely new design for the automatic transmission.

Models

1964: K4B 050

The first model with this new layout was the K4B 050 (without type designation). Beside the new layout the number of pinions is doubled from 3 to 6 to handle the much higher torque of the big block V8 engine.

1967: K4C 025

After the satisfactory experience with the new design, it was adopted in 1967 for the new core model K4C 025 (Type 722.2) of the first automatic transmission series from Mercedes-Benz. With the small block V8 engine M 116, the K4A 040 (Type 722.2) was launched as a reinforced version of the same design.

1972: W4B 025

When the torque converter technique was fully established, the fluid coupling was replaced by a torque converter for the smaller engines, which leads to the W4B 025 (type 722.1).^[4] Used in L4, L5 and L6 engines due to its lower torque output. In normal situations, it rests stationary in 2nd gear, but it will use 1st gear when the vehicle starts moving and throttle is applied^[5] or if L position is selected in gear selector.

Variants For Commercial Cars

The W4A 018 (type 720.1) was derived from the W4B 025 (type 722.1) for vans up to 5,600 kg (12,350 lb)^[6] and off road vehicles, the W4B 035 from the W4B 025 (type 722.1) and K4A 040 (type 722.2) for light trucks up to 13,000 kg (28,660 lb).^[7] The main difference is the use of straight-cut planetary gearsets instead of helical-cut ones for better fuel efficiency at the price of lower noise comfort.

Specifications

For this second 4-speed models^[a] 8 main components^[b] are used.^[4]

1. plus 1 reverse gear
2. 3 simple planetary gearsets, 3 brakes, 2 clutches

Gear Ratios

With Assessment		Planetary Gearset: Teeth[a]			Count	Total[b] Center[c]	Avg.[d]
		Simpson		Simple
Model Type	Version First Delivery	S1[e] R1[f]	S2[g] R2[h]	S3[i] R3[j]	Brakes Clutches	Ratio Span	Gear Step[k]
Gear Ratio		R ${\displaystyle {i_{R}}}$		1 ${\displaystyle {i_{1}}}$	2 ${\displaystyle {i_{2}}}$	3 ${\displaystyle {i_{3}}}$	4 ${\displaystyle {i_{4}}}$
Step[k]		${\displaystyle -{\tfrac {i_{R}}{i_{1}}}}$[l]		${\displaystyle {\tfrac {i_{1}}{i_{1}}}}$	${\displaystyle {\tfrac {i_{1}}{i_{2}}}}$[m]	${\displaystyle {\tfrac {i_{2}}{i_{3}}}}$	${\displaystyle {\tfrac {i_{3}}{i_{4}}}}$
Δ Step[n][o]					${\displaystyle {\tfrac {i_{1}}{i_{2}}}:{\tfrac {i_{2}}{i_{3}}}}$	${\displaystyle {\tfrac {i_{2}}{i_{3}}}:{\tfrac {i_{3}}{i_{4}}}}$
Shaft Speed		${\displaystyle {\tfrac {i_{1}}{i_{R}}}}$		${\displaystyle {\tfrac {i_{1}}{i_{1}}}}$	${\displaystyle {\tfrac {i_{1}}{i_{2}}}}$	${\displaystyle {\tfrac {i_{1}}{i_{3}}}}$	${\displaystyle {\tfrac {i_{1}}{i_{4}}}}$
Δ Shaft Speed[p]		${\displaystyle 0-{\tfrac {i_{1}}{i_{R}}}}$		${\displaystyle {\tfrac {i_{1}}{i_{1}}}-0}$	${\displaystyle {\tfrac {i_{1}}{i_{2}}}-{\tfrac {i_{1}}{i_{1}}}}$	${\displaystyle {\tfrac {i_{1}}{i_{3}}}-{\tfrac {i_{1}}{i_{2}}}}$	${\displaystyle {\tfrac {i_{1}}{i_{4}}}-{\tfrac {i_{1}}{i_{3}}}}$
K4B 050 N/A	51 kp⋅m (369 lb⋅ft) 1964	50 76	44 76	44 76	3 2	3.9789 1.9947	1.5846[k]
Gear Ratio		−4.1455 ${\displaystyle -{\tfrac {228}{55}}}$		3.9789 ${\displaystyle {\tfrac {378}{95}}}$	2.4589 ${\displaystyle {\tfrac {1,168}{475}}}$	1.5789[o]	1.0000 ${\displaystyle {\tfrac {1}{1}}}$
Step		1.0418		1.0000	1.6182	1.5573	1.5789
Δ Step[n]					1.0391	0.9863[o]
Speed		-0.9598		1.0000	1.6182	2.5200	3.9789
Δ Speed		0.9598		1.0000	0.6182	0.9018	1.4589
K4C 025 722.2	25 kp⋅m (181 lb⋅ft) 1967[6]	44 76	44 76	35 76	3 2	3.9833 1.9958	1.5852[k]
Gear Ratio		−5.4779[l] ${\displaystyle -{\tfrac {2,109}{385}}}$		3.9833 ${\displaystyle {\tfrac {1,665}{418}}}$	2.3855[m][o] ${\displaystyle {\tfrac {5,439}{2,280}}}$	1.4605[k] ${\displaystyle {\tfrac {111}{76}}}$	1.0000 ${\displaystyle {\tfrac {1}{1}}}$
Step		1.3752[l]		1.0000	1.6698[m]	1.6333[k]	1.4605
Δ Step[n]					1.0223[o]	1.1183
Speed		-0.7271		1.0000	1.6696	2.7273	3.9833
Δ Speed		0.7271		1.0000	0.6696	1.0575	1.2560
K4A 040 722.2	40 kp⋅m (289 lb⋅ft) 1969	44 76	44 76	35 76	3 2	3.9833 1.9958	1.5852[k]
Ratio		−5.4779[l]		3.9833	2.3855[m][o]	1.4605[k]	1.0000
W4B 025 722.1	25 kp⋅m (181 lb⋅ft) 1972[6]	44 76	44 76	35 76	3 2	3.9833 1.9958	1.5852[k]
Ratio		−5.4779[l]		3.9833	2.3855[m][o]	1.4605[k]	1.0000
W4A 018[q] 720.1	18 kp⋅m (130 lb⋅ft) 1975	46 80	46 80	37 80	3 2	4.0060 2.0015	1.5882[k]
Gear Ratio		−5.4994[l] ${\displaystyle -{\tfrac {4,680}{851}}}$		4.0060 ${\displaystyle {\tfrac {7,371}{1840}}}$	2.3911[m][o] ${\displaystyle {\tfrac {1,339}{560}}}$	1.4625[k] ${\displaystyle {\tfrac {117}{80}}}$	1.0000 ${\displaystyle {\tfrac {1}{1}}}$
Step		1.3728[l]		1.0000	1.6754[m]	1.6349[k]	1.4625
Δ Step[n]					1.0248[o]	1.1179
Speed		-0.7284		1.0000	1.6754	2.7391	4.0060
Δ Speed		0.7284		1.0000	0.6754	1.0637	1.2668
W4B 035[r] N/A	35 kp⋅m (253 lb⋅ft) 1975	42 78	42 78	36 78	3 2	4.1758 2.0435	1.6103[k]
Gear Ratio		−5.8810[l] ${\displaystyle -{\tfrac {2,223}{378}}}$		4.1758 ${\displaystyle {\tfrac {3,420}{819}}}$	2.4115[m][o] ${\displaystyle {\tfrac {627}{260}}}$	1.4615[k] ${\displaystyle {\tfrac {57}{39}}}$	1.0000 ${\displaystyle {\tfrac {1}{1}}}$
Step		1.4083[l]		1.0000	1.7360[m]	1.6500[k]	1.4615
Δ Step[n]					1.0495[o]	1.1289
Speed		-0.7101		1.0000	1.7316	2.8571	4.1758
Δ Speed		0.7101		1.0000	0.7316	1.1255	1.3187
Ratio R & Even		${\displaystyle -{\tfrac {R_{1}(S_{3}+R_{3})}{S_{1}S_{3}}}}$		${\displaystyle {\tfrac {(S_{1}(S_{2}+R_{2})+R_{1}S_{2})(S_{3}+R_{3})}{S_{1}(S_{2}+R_{2})R_{3}}}}$			${\displaystyle {\tfrac {1}{1}}}$
Ratio Odd			${\displaystyle i_{1}={\tfrac {(S_{1}+R_{1})(S_{3}+R_{3})}{S_{1}R_{3}}}}$			${\displaystyle i_{3}={\tfrac {S_{3}+R_{3}}{R_{3}}}}$
Algebra And Actuated Shift Elements
Brake A[s]					❶
Brake B[t]				❶	❶	❶
Brake R[u]		❶
Clutch D[v]						❶	❶
Clutch E[w]		❶		❶			❶
Layout Input and output are on opposite sides Planetary gearset 1 is on the input (turbine) side Input shafts is S1 Output shaft is C3 (the carrier of gearset 3) Total Ratio Span (Total Ratio Spread · Total Gear Ratio) ${\displaystyle {\tfrac {i_{1}}{i_{n}}}}$ A wider span enables the downspeeding when driving outside the city limits increase the climbing ability when driving over mountain passes or off-road or when towing a trailer Ratio Span's Center ${\displaystyle (i_{1}i_{n})^{\tfrac {1}{2}}}$ The center indicates the speed level of the transmission Together with the final drive ratio it gives the shaft speed level of the vehicle Average Gear Step ${\displaystyle ({\tfrac {i_{1}}{i_{n}}})^{\tfrac {1}{n-1}}}$ With decreasing step width the gears connect better to each other shifting comfort increases Sun 1: sun gear of gearset 1 Ring 1: ring gear of gearset 1 Sun 2: sun gear of gearset 2 Ring 2: ring gear of gearset 2 Sun 3: sun gear of gearset 3 Ring 3: ring gear of gearset 3 Standard 50:50 — 50 % Is Above And 50 % Is Below The Average Gear Step — With steadily decreasing gear steps (yellow highlighted line Step) and a particularly large step from 1st to 2nd gear the lower half of the gear steps (between the small gears; rounded down, here the first 1) is always larger and the upper half of the gear steps (between the large gears; rounded up, here the last 2) is always smaller than the average gear step (cell highlighted yellow two rows above on the far right) lower half: smaller gear steps are a waste of possible ratios (red bold) upper half: larger gear steps are unsatisfactory (red bold) Standard R:1 — Reverse And 1st Gear Have The Same Ratio — The ideal reverse gear has the same transmission ratio as 1st gear no impairment when maneuvering especially when towing a trailer a torque converter can only partially compensate for this deficiency Plus 11.11 % minus 10 % compared to 1st gear is good Plus 25 % minus 20 % is acceptable (red) Above this is unsatisfactory (bold) Standard 1:2 — Gear Step 1st To 2nd Gear As Small As Possible — With continuously decreasing gear steps (yellow marked line Step) the largest gear step is the one from 1st to 2nd gear, which for a good speed connection and a smooth gear shift must be as small as possible A gear ratio of up to 1.6667:1 (5:3) is good Up to 1.7500:1 (7:4) is acceptable (red) Above is unsatisfactory (bold) From large to small gears (from right to left) Standard STEP — From Large To Small Gears: Steady And Progressive Increase In Gear Steps — Gear steps should increase: Δ Step (first green highlighted line Δ Step) is always greater than 1 As progressive as possible: Δ Step is always greater than the previous step Not progressively increasing is acceptable (red) Not increasing is unsatisfactory (bold) Standard SPEED — From Small To Large Gears: Steady Increase In Shaft Speed Difference — Shaft speed differences should increase: Δ Shaft Speed (second line marked in green Δ (Shaft) Speed) is always greater than the previous one 1 difference smaller than the previous one is acceptable (red) 2 consecutive ones are a waste of possible ratios (bold) for light duty trucks up to 5,600 kg (12,350 lb)[6][8] for medium duty trucks up to 13,000 kg (28,660 lb)[7][9] Blocks S2 Blocks S3 Blocks C1(the carrier of gearset 1) Couples S2 with C2 (the carrier of gearset 2) Couples R1 with S3

1971: W3A 040 And Follow-Up Products — 3-Speed Transmissions With 2 Planetary Gearsets —

Layout

When the torque converter technique was fully established, 3-speed units, the W3A 040 and W3B 050 (type 722.0) is combined with V8 engines, and it uses torque converter instead of fluid coupling.^[1][4] The transmission saves 1 planetary gearset and uses the same housing as the 4-speed versions. The free space therefore is used to reinforce the shift elements (brakes and clutches) to handle the higher torque of the V8 engines.

First the W3A 040 was released for the all new M117 V8 engine of the W 108 and W 109 in 1971. The second in the series is the W3B 050, which was released initially for the W 116 450 SE/SEL in 1973. At that time the 4-speed transmission for the 350 SE/SEL was replaced by this 3-speed model. The reinforced W3B 050 reinforced (type 722.003) is the strongest of the series, able to handle the input of the enlarged version of the M 100, the biggest Mercedes-Benz engine in post-war history,^[10] exclusively used in the W 116 450 SEL 6.9.

Specifications

For the 3-speed models^[a] 7 main components^[b] are used, which shows economic equivalence with the direct competitor.

1. plus 1 reverse gear
2. 2 simple planetary gearsets,^[4] 3 brakes, 2 clutches

Gear Ratios

With Assessment		Simple Planetary Gearset: Teeth[a]		Count	Total[b] Center[c]	Avg.[d]
Model Type	Version First Delivery	S1[e] R1[f]	S2[g] R2[h]	Brakes Clutches	Ratio Span	Gear Step[i]
Gear Ratio		R ${\displaystyle {i_{R}}}$		1 ${\displaystyle {i_{1}}}$	2 ${\displaystyle {i_{2}}}$	3 ${\displaystyle {i_{3}}}$
Step[i]		${\displaystyle -{\tfrac {i_{R}}{i_{1}}}}$[j]		${\displaystyle {\tfrac {i_{1}}{i_{1}}}}$	${\displaystyle {\tfrac {i_{1}}{i_{2}}}}$[k]	${\displaystyle {\tfrac {i_{2}}{i_{3}}}}$
Δ Step[l][m]					${\displaystyle {\tfrac {i_{1}}{i_{2}}}:{\tfrac {i_{2}}{i_{3}}}}$
Shaft Speed		${\displaystyle {\tfrac {i_{1}}{i_{R}}}}$		${\displaystyle {\tfrac {i_{1}}{i_{1}}}}$	${\displaystyle {\tfrac {i_{1}}{i_{2}}}}$	${\displaystyle {\tfrac {i_{1}}{i_{3}}}}$
Δ Shaft Speed[n]		${\displaystyle 0-{\tfrac {i_{1}}{i_{R}}}}$		${\displaystyle {\tfrac {i_{1}}{i_{1}}}-0}$	${\displaystyle {\tfrac {i_{1}}{i_{2}}}-{\tfrac {i_{1}}{i_{1}}}}$	${\displaystyle {\tfrac {i_{1}}{i_{3}}}-{\tfrac {i_{1}}{i_{2}}}}$
W4A 040 722.0	40 kp⋅m (289 lb⋅ft) 1971[11]	44 76	35 76	3 2	2.3061 1.5186	1.5186[i]
Gear Ratio		−1.8361[j] ${\displaystyle -{\tfrac {1,221}{665}}}$		2.3061 ${\displaystyle {\tfrac {1,665}{722}}}$	1.4605 ${\displaystyle {\tfrac {63}{25}}}$	1.0000 ${\displaystyle {\tfrac {1}{1}}}$
Step		0.7962[j]		1.0000	1.5789	1.4605
Δ Step[l]					1.0811
Speed		-1.2560		1.0000	1.5789	2.3061
Δ Speed		1.2560		1.0000	0.5789	0.9411
W4A 050 722.0	50 kp⋅m (362 lb⋅ft) 1973[11]	44 76	35 76	3 2	2.3061 1.5186	1.5186[i]
Ratio		−1.8361[j]		2.3061	1.4605	1.0000
W4A 050 reinf. 722.0	56 kp⋅m (405 lb⋅ft) 1975[11]	44 76	35 76	3 2	2.3061 1.5186	1.5186[i]
Ratio		−1.8361[j]		2.3061	1.4605	1.0000
Ratio	${\displaystyle -{\tfrac {S_{1}(S_{2}+R_{2})}{R_{1}S_{2}}}}$		${\displaystyle {\tfrac {(S_{1}+R_{1})(S_{2}+R_{2})}{R_{1}R_{2}}}}$		${\displaystyle {\tfrac {S_{2}+R_{2}}{R_{2}}}}$	${\displaystyle {\tfrac {1}{1}}}$
Algebra And Actuated Shift Elements
Brake A[o]				❶
Brake B[p]				❶	❶
Brake R[q]		❶
Clutch D[r]					❶	❶
Clutch E[s]		❶				❶
Layout Input and output are on opposite sides Planetary gearset 1 is on the input (turbine) side Input shafts is R1 Output shaft is C2 (the carrier of gearset 2) Total Ratio Span (Total Ratio Spread · Total Gear Ratio) ${\displaystyle {\tfrac {i_{1}}{i_{n}}}}$ A wider span enables the downspeeding when driving outside the city limits increase the climbing ability when driving over mountain passes or off-road or when towing a trailer Ratio Span's Center ${\displaystyle (i_{1}i_{n})^{\tfrac {1}{2}}}$ The center indicates the speed level of the transmission Together with the final drive ratio it gives the shaft speed level of the vehicle Average Gear Step ${\displaystyle ({\tfrac {i_{1}}{i_{n}}})^{\tfrac {1}{n-1}}}$ With decreasing step width the gears connect better to each other shifting comfort increases Sun 1: sun gear of gearset 1 Ring 1: ring gear of gearset 1 Sun 2: sun gear of gearset 2 Ring 2: ring gear of gearset 2 Standard 50:50 — 50 % Is Above And 50 % Is Below The Average Gear Step — With steadily decreasing gear steps (yellow highlighted line Step) and a particularly large step from 1st to 2nd gear the lower half of the gear steps (between the small gears; rounded down, here the first 1) is always larger and the upper half of the gear steps (between the large gears; rounded up, here the last 1) is always smaller than the average gear step (cell highlighted yellow two rows above on the far right) lower half: smaller gear steps are a waste of possible ratios (red bold) upper half: larger gear steps are unsatisfactory (red bold) Standard R:1 — Reverse And 1st Gear Have The Same Ratio — The ideal reverse gear has the same transmission ratio as 1st gear no impairment when maneuvering especially when towing a trailer a torque converter can only partially compensate for this deficiency Plus 11.11 % minus 10 % compared to 1st gear is good Plus 25 % minus 20 % is acceptable (red) Above this is unsatisfactory (bold) Standard 1:2 — Gear Step 1st To 2nd Gear As Small As Possible — With continuously decreasing gear steps (yellow marked line Step) the largest gear step is the one from 1st to 2nd gear, which for a good speed connection and a smooth gear shift must be as small as possible A gear ratio of up to 1.6667:1 (5:3) is good Up to 1.7500:1 (7:4) is acceptable (red) Above is unsatisfactory (bold) From large to small gears (from right to left) Standard STEP — From Large To Small Gears: Steady And Progressive Increase In Gear Steps — Gear steps should increase: Δ Step (first green highlighted line Δ Step) is always greater than 1 As progressive as possible: Δ Step is always greater than the previous step Not progressively increasing is acceptable (red) Not increasing is unsatisfactory (bold) Standard SPEED — From Small To Large Gears: Steady Increase In Shaft Speed Difference — Shaft speed differences should increase: Δ Shaft Speed (second line marked in green Δ (Shaft) Speed) is always greater than the previous one 1 difference smaller than the previous one is acceptable (red) 2 consecutive ones are a waste of possible ratios (bold) Blocks S1 Blocks S2 Blocks C1(the carrier of gearset 1) Couples S1 with C1 (the carrier of gearset 2) Couples S1 with S2

Applications

K4A 025

• 1961–1965 (saloon) · 1961–1968 (coupé/convertible) W 111
• 1961–1965 (saloon) · 1962–1968 (coupé/convertible) W 112
• 1961–1968 W 110
• 1963–1971 W 113
• 1965–1968 W 108/W 109

K4B 050

• 1963–1981 600 (W 100)
• 1968–1972 300 SEL 6.3 (W 109)

K4C 025

• 1968–1971 (coupé/convertible) W 111
• 1968–1972 W 108/W 109

W 114/W 115

Chassis code	Car model	Engine code	Transmission code
114.015 and 114.615	230.6	180.954	722.203
114.017 and 114.617	230.6 Lang
114.011 and 114.611	250	130.923	722.204
114.023 and 114.623	250 C
114.060 and 114.660	280	110.921	722.202
114.073 and 114.673	280 C
114.062 and 114.662	280 E	110.981	722.200
114.072 and 114.672	280 CE
115.015 and 115.615	200	115.923	722.205
115.010	220	115.920
115.115 and 115.715	200 D	615.913	722.206
115.110 and 115.710	220 D	615.912
115.112	220 D Lang

K4A 040

W 108/W 109

Chassis code	Car model	Engine code	Transmission code	Notes
109.057	300 SEL 3.5	3.5 L M 116 V8	722.201	worldwide except USA
108.067	280 SE 3.5
108.068	280 SEL 3.5

R 107/C 107

Chassis code	Car model	Engine code	Transmission code
107.043	350 SL	116.982 (D-Jet) 116.984 (K-Jet)	722.201
107.023	350 SLC

W3A 040

W 108/W 109

Chassis code	Car model	Engine code	Transmission code	Notes
109.056	300 SEL 4.5	4.5 L M 117 V8	722.000	USA only
108.057	280 SE 4.5
108.058	280 SEL 4.5

R 107/C 107

Chassis code	Car model	Engine code	Transmission code	Notes
107.043	350 SL	116.982 (D-Jet) 116.984 (K-Jet)	722.002
107.023	350 SLC
107.044	450 SL	117.982 (D-Jet) 117.985 (K-Jet)	722.004	USA and Japan only
107.024	450 SLC

W 116

Chassis code	Car model	Engine code	Transmission code	Notes
116.028	350 SE	116.983 (D-Jet) 116.985 (K-Jet)	722.002
116.029	350 SEL
116.032	450 SE	117.983 (D-Jet) 117.986 (K-Jet)	722.004	USA and Japan only
116.033	450 SEL

W3B 050

R 107/C 107

Chassis code	Car model	Engine code	Transmission code	Notes
107.044	450 SL	117.982 (D-Jet) 117.985 (K-Jet)	722.001	worldwide except USA and Japan
107.024	450 SLC

W 116

Chassis code	Car model	Engine code	Transmission code	Notes
116.032	450 SE	117.983 (D-Jet) 117.986 (K-Jet)	722.001	worldwide except USA and Japan
116.033	450 SEL
116.036	450 SEL 6.9	100.985	722.003	722.003 W3B 050 reinforced[12]

W4B 025

R 107/C 107

Chassis code	Car model	Engine code	Transmission code
107.042	280 SL	110.982 110.986 110.990	722.103 722.112
107.022	280 SLC	110.982 110.986

W 114/W 115

Chassis code	Car model	Engine code	Transmission code
114.015 and 114.615	230.6	180.954	722.105
114.017 and 114.617	230.6 Lang
114.011 and 114.611	250	130.923	722.104
114.023 and 114.623	250 C
114.060 and 114.660	280	110.921	722.102
114.073 and 114.673	280 C
114.062 and 114.662	280 E	110.981	722.103
114.072 and 114.672	280 CE
115.015 and 115.615	200	115.923	722.106
115.017	230.4	115.951	722.110
115.115 and 115.715	200 D	615.913	722.107
115.110 and 115.710	220 D	615.912
115.112	220 D Lang
115.117	240 D	616.916	722.108
115.119	240 D Lang
115.114	240 D 3.0	617.910	722.109

W 116

Chassis code	Car model	Engine code	Transmission code	Notes
116.020	280 S	110.922	722.100 722.102 722.111
116.024	280 SE	110.983 (D-Jet) 110.985 (K-Jet)	722.101 722.103 722.112
116.025	280 SEL
116.120	300 SD	617.950	722.120	USA only

W 123

Chassis code	Car model	Engine code	Transmission code	Notes
123.020	200	115.938 115.939	722.115
123.220	200	102.920 102.939	722.121
123.280	200 T
123.023	230	115.954	722.119
123.083	230 T
123.043	230 C
123.223	230 E	102.980	722.122
123.283	230 TE
123.243	230 CE
123.026	250	123.920 123.921	722.113
123.086	250 T
123.028	250 Lang
123.030	280	110.923	722.111
123.050	280 C
123.033	280 E	110.984 110.988	722.112
123.093	280 TE
123.053	280 CE
123.120	200 D	615.940	722.116
123.126	220 D	615.941
123.123	240 D	616.912	722.117
123.183	240 TD
123.125	240 D Lang
123.130	300 D	617.912	722.118
123.190	300 TD
123.132	300 D Lang
123.150	300 CD			USA only

See also

• Cars portal

• List of Daimler AG transmissions