Ship motions

Not to be confused with Ship movements.

Ship motions are the six degrees of freedom that a ship, boat, or other watercraft can experience.

Aircraft carrier rolling during a typhoon.

Reference axes

See also: Aircraft principal axes

The vertical/Z axis, or yaw axis, is an imaginary line running vertically through the ship and through its centre of mass. A yaw motion is a side-to side movement of the bow and stern of the ship.

The transverse/Y axis, lateral axis, or pitch axis is an imaginary line running horizontally across the ship and through the centre of mass. A pitch motion is an up-or-down movement of the bow and stern of the ship.

The longitudinal/X axis, or roll axis, is an imaginary line running horizontally through the length of the ship, through its centre of mass, and parallel to the waterline. A roll motion is a side-to-side or port-starboard tilting motion of the superstructure around this axis.

Rotational

Axes of a ship and rotations around them

For other uses, see Euler angles § Tait–Bryan angles.

There are three special axes in any ship, called longitudinal, transverse and vertical axes. The angular movements around them—affecting the ship’s moment of inertia, which sets the torque it requires to rotate in any direction—are the ship’s rotational motions (or rotary motions), known as roll, pitch, and yaw respectively.

Roll

The tilting rotation of a vessel about its longitudinal/X (front-back or bow-stern) axis. An offset or deviation from normal on this axis is referred to as list or heel. Heel refers to an offset that is intentional or expected, as caused by wind pressure on sails, turning, or other crew actions. The rolling motion towards a steady state (or list) angle due to the ship's own weight distribution is referred in marine engineering as list. List normally refers to an unintentional or unexpected offset, as caused by flooding, battle damage, shifting cargo, etc.

Pitch

The up/down rotation of a vessel about its transverse/Y (side-to-side or port-starboard) axis. An offset or deviation from normal on this axis is referred to as trim or out of trim. A vessel that is pitching back and forth is usually termed to be hobby horsing.

Yaw

The turning rotation of a vessel about its vertical/Z axis. An offset or deviation from normal on this axis is referred to as deviation or set. This is referred to as the heading of the boat relative to a magnetic compass (or true heading if referenced to the true north pole); it also affects the bearing.

Translational

Translations

Besides a ship’s own rotational motion, over which it has a measure of control, the water in which it moves can have motion independent of the ship, which displaces the ship by imposing forces that shift the ship’s entire mass linearly along any of its axes—longitudinal, transverse, and vertical. These translational motions (or translatory motions) are known as surge, sway, and heave respectively.^[1][2]

Surge

The linear longitudinal (front/back or bow/stern) motion imparted by maritime conditions, usually head or following seas, or by accelerations imparted by the propulsion system.

Sway

The linear transverse (side-to-side or port-starboard) motion. This motion is generated directly either by the water and wind motion, particularly lateral wave motion, exerting forces against the hull or by the ship's own propulsion; or indirectly by the inertia of the ship while turning. This movement can be compared to the vessel's lateral drift from its course.

Heave

The linear vertical (up/down) motion; excessive downward heave can swamp a ship.

Stabilization

There are methods for both passive and active motion stabilization used in some designs. They include static hull features such as skegs and bilge keels, or active mechanical devices like counterweights, antiroll tanks and stabilizers.

See also

• Jibe – Basic sailing maneuver, where ship turns its stern through the wind
• Tacking (sailing) – Sailing maneuver
• Translation (physics) – Planar movement within a Euclidean space without rotationPages displaying short descriptions of redirect targets
• Rotation – Movement of an object around an axis
• Naval architecture – Engineering discipline of marine vessels
• Seakeeping – Response of a vessel to sea conditions
• Stern suction – Tendency of the stern of a ship making way to swing toward the near bankPages displaying short descriptions of redirect targets
• Ship stability – Ship response to disturbance from an upright condition
• Ship motion test – Scale model a hydrodynamic test to predict full size behaviour
• Six degrees of freedom – Types of movement possible for a rigid body in three-dimensional space
• Flight dynamics – Study of the performance, stability, and control of flying vehicles